13 inch COLOR TV/DVD
Owner's Manual
6513DG
FEATURES
• Auto Channel Programming
• Screen Saver
• Auto Power Off
• Parental Lock
• Resume Play
• Closed Caption Decoder
SUPPLIED ACCESSORIES
This unit comes with the following accessories. Please confirm that
all the accessories are included.
Owner's Manual
P Remote Control
P AA batteries x 2
P Owner's Manual
(NF100UD)
(1EMN21312)
INSTRUCCIONES EN ESPAÑOL INCLUDAS
PLEASE READ BEFORE USING THIS EQUIPMENT
IF YOU NEED ADDITIONAL ASSISTANCE FOR SET-UP OR OPERATING
AFTER READING OWNER'S MANUAL,
PLEASE CALL TOLL FREE 1-800-968-3429 OR VISIT OUR WEB SITE AT
14. Lightning - For added protection for this unit receiver during
a lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the unit due to lightning and power-line surges.
15. Power Lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other elec-
tric light or power circuits, or where it can fall into such power
lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
16. Overloading - Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry - Never push objects of any kind
into this unit through openings as they may touch dangerous
voltage points or short out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the unit.
18. Servicing - Do not attempt to service this unit yourself as
opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified ser-
vice personnel.
a. When the power-supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the operat-
ing instructions. Adjust only those controls that are covered
by the operating instructions, as improper adjustment of
other controls may result in damage and will often require
extensive work by a qualified technician to restore the unit to
its normal operation.
e. If the unit has been dropped or damaged in any way.
f. When the unit exhibits a distinct change in performance, this
indicates a need for service.
20. Replacement Parts - When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer that have the same character-
istics as the original part. Unauthorized substitutions may
result in fire, electric shock, injury to persons or other haz-
ards.
21. Safety Check - Upon completion of any service or repairs to
this unit, ask the service technician to perform routine safety
checks to determine that the unit is in proper operating con-
dition.
22. Heat - This unit product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
19. Damage Requiring Service - Unplug this unit from the wall
outlet and refer servicing to qualified service personnel
under the following conditions:
IMPORTANT COPYRIGHT INFORMATION
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellec-
tual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is
intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio commu-
nications. However, there is no guarantee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to
this equipment may cause harmful interference unless the modifications are expressly approved in the
owner’s manual. The user could lose the authority to operate this equipment if an unauthorized change or
modification is made.
3
EN
LASER SAFETY
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service
this device, due to possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED.
DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU'AU FOND.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guide-
lines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding system
of the building as close to the point of cable entry as practical.
LOCATION
For safe operation and satisfactory performance of the unit, keep the following in mind when selecting a place
for its installation:
• Shield it from direct sunlight and keep it away from sources of intense heat.
• Avoid dusty or humid places.
• Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the
top and bottom of the unit. Do not place the unit on a carpet because this will block the ventilation holes.
• Install unit in a horizontal position.
• Avoid locations subject to strong vibration.
• Do not place the unit near strong magnetic fields.
• Avoid moving unit to locations where temperature differences are extreme.
• Be sure to remove disc and unplug the AC power cord from the outlet before carrying the unit.
TO AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from an AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on your unit, unplug the power cord immediately and take the unit to our
Authorized Service Center for servicing.
• Do not put your fingers or objects into the unit disc loading tray.
• Do not place anything directly on top of the unit.
MOISTURE WARNING
• Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or
after heating a cold room or under conditions of high humidity. If you play a videotape or DVD in a moist
unit, it may damage the tape or DVD and the unit. When the condensation occurs inside the unit, turn the
unit on and leave it at least 2 hours to dry out.
NOTE ABOUT RECYCLING
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-
tions concerning chemical wastes.
Manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks of Dolby Laboratories.
The serial number of this product may be found on the back of the unit. No other unit has the same serial
number as yours. You should record the number and other vital information here and retain this book as a
permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
4
EN
ABLE OF CONTENTS
T
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . .2
TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . .5
SYMBOLS USED IN THIS MANUAL . . . . . . . . . . . .5
PREPARATION FOR USE . . . . . . . . . . . . . . . . . .6
ANTENNA/CABLE CONNECTIONS . . . . . . . . . . . .6
CONNECTING TO AN EXTERNAL DEVICE (FRONT) . .7
INSTALLING THE BATTERIES IN REMOTE CONTROL .7
OPERATING CONTROLS AND FUNCTIONS . . .8
PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . .15
BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . .15
DISC MENU / TITLE MENU . . . . . . . . . . . . . . . . . .15
SPECIAL PLAYBACK FUNCTIONS & SETTINGS . . .16
FUNCTION TABLE . . . . . . . . . . . . . . . . . . . . . . . .16
AUDIO MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
SUBTITLE LANGUAGE . . . . . . . . . . . . . . . . . . . . .17
ANGLE MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
ZOOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
BLACK LEVEL MENU . . . . . . . . . . . . . . . . . . . . . .18
SEARCH MENU . . . . . . . . . . . . . . . . . . . . . . . . . .18
REPEAT PLAYBACK . . . . . . . . . . . . . . . . . . . . . . .19
PROGRAMMED PLAYBACK . . . . . . . . . . . . . . . . .20
RANDOM PLAYBACK . . . . . . . . . . . . . . . . . . . . . .20
ON-SCREEN INFORMATION . . . . . . . . . . . . . .20
CHANGING THE DVD SET UP ITEMS . . . . . . .21
CUSTOM MENU . . . . . . . . . . . . . . . . . . . . . . . . . .21
INITIALIZE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . .24
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . .26
APPENDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
CABLE CHANNEL DESIGNATIONS . . . . . . . . . . .27
LANGUAGE CODE LIST . . . . . . . . . . . . . . . . . . . .27
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . .28
TV SECTION
TV OPERATION AND SETTINGS . . . . . . . . . . . .9
INITIAL SET UP . . . . . . . . . . . . . . . . . . . . . . . . . . .9
WATCHING A TV PROGRAM . . . . . . . . . . . . . . . . .9
SLEEP TIMER / PICTURE CONTROL . . . . . . . . . .10
CLOSED CAPTION SYSTEM . . . . . . . . . . . . . . . .10
CHANNEL SET UP . . . . . . . . . . . . . . . . . . . . . . . .11
ON-SCREEN MENU LANGUAGE . . . . . . . . . . . . .11
V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . . . .12
DVD SECTION
ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . .14
PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . . . . . .14
UNPLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . . .14
ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . .29
WARRANTY . . . . . . . . . . . . . . . . . .BACK COVER
SYMBOLS USED IN THIS MANUAL
The following symbols below appear in some headings and notes in this manual, with the following meanings.
Description refers to TV operation
(in the TV mode).
Description refers to playback of
audio CDs (in the DVD mode).
TV
TV
Description refers to playback of
DVD video discs (in the DVD mode).
Description refers to the items
to be set by the QUICK mode
(in the DVD mode).
QUICK
5
EN
REPARATION FOR USE
P
ANTENNA/CABLE CONNECTIONS
Plug the incoming cable into the ANT. jack on the rear of the unit.
If your cable service supplies you with a converter box or if you use a satellite system, connect the box with
this unit as shown below.
Cable
TV signal
Antenna
or
Incoming cable from home
Antenna / Cable Company
(No Cable Box)
ANT.
Rear of the unit
ANT.
Cable Box or Satellite Box*
OR
OUT
IN
*NOTE
Incoming cable from Cable Company
or Satellite Antenna
(DO NOT DISCONNECT FROM BOX)
Some cable TV systems use scrambled
signals and require a special converter to
receive these channels. Consult your local
cable company.
NOTE:
Bent pin
For your safety and to
Before plugging the antenna into
the ANT. jack of the unit, check
that the pin is not bent. If it is bent,
straighten the pin as illustrated,
then plug the pin into the ANT. jack
of the unit.
avoid damages to the unit,
unplug the antenna cable
from the ANT. jack before
Cable
Plug
(Needs to be
straightened)
(Straight pin)
moving the unit.
6
EN
CONNECTING TO AN EXTERNAL DEVICE (FRONT)
When you watch a program recorded on another source (VCR or video camera), use the
AUDIO/VIDEO input jacks on the front of the unit.
AUX
Connect the Audio/Video output jacks of another source to the AUDIO and VIDEO jacks of
this unit.
Then use [SELECT] or [CH. K / L] until "AUX" appears on the screen.
ex.
[Front of the unit]
VCR or video camera, etc.
To the Audio output jack
(IN)
(OUT)
Audio Cable
OPEN / CLOSE
(commercially available)
VIDEO
AUDIO
HEADPHONE
(IN)
To the Video output jack
Video Cable
(OUT)
(commercially available)
INSTALLING THE BATTERIES IN REMOTE CONTROL
1) Open the battery compartment cover by pressing
[BATTERY PRECAUTIONS]
the cover on the remote unit in the direction of
the arrow.
2) Insert 2 “AA” penlight batteries into the battery
compartment in the direction indicated by the
polarity (+/-) markings.
Be sure to follow the correct polarity as indicat-
ed in the battery compartment. Reversed batter-
ies may cause damage to the device.
•
•
•
•
Do not mix different types of batteries together
(e.g. Alkaline and Carbon-Zinc) or old batteries
with fresh ones.
3) Replace the cover.
If the device is not to be used for a long period
of time, remove the batteries to prevent damage
or injury from possible battery leakage.
1
2
3
Do not try to recharge batteries not intended to
be recharged; they can overheat and rupture.
7
EN
PERATING CONTROLS AND FUNCTIONS
O
- FRONT PANEL -
1
2
3
4 5
6
7
8
9 10
11
- REMOTE CONTROL -
[REMOTE CONTROL]
12 POWER Button [TV P.9 / DVD P.15]
13 PICTURE/SLEEP Button [TV P.10]
14 Number Buttons [TV P.9 / DVD P.18]
15 DISPLAY Button [DVD P.20]
16 SKIP H / G Buttons [DVD P.18]
17 PLAY B Button [TV P.9 / DVD P.15]
18 PAUSE F Button [DVD P.15]
19 TITLE Button [DVD P.15]
20 CLEAR Button [TV P.10 / DVD P.18]
21 MODE Button [DVD P.16]
OPEN/
CLOSE
POWER
PICTURE/
SLEEP
SELECT
22
23
12
13
1
4
3
6
9
2
5
8
0
14
CH.
24
7
VOL.
DISPLAY
+100
25
26
27
28
+10
15
SKIP
SET-UP
MUTE
22 OPEN/CLOSE A Button [DVD P.15]
23 SELECT Button [TV P.9]
16
17
PLAY
FWD
REV
K
L
24 CH.
/
Buttons [TV P.9]
Buttons [TV P.9]
STOP
29
X
Y
25 VOL.
/
SLOW
PAUSE
CLEAR
MODE
TITLE
DISC MENU
26 MUTE Button [TV P.9]
18
19
20
30
31
32
ENTER
27 SET-UP Button [TV P.10 / DVD P.21]
28 REV E Button [DVD P.15]
FWD D Button [DVD P.15]
RETURN
33
21
29 STOP C Button [DVD P.15]
30 DISC MENU Button [DVD P.15]
31 ENTER Button [TV P.10 / DVD P.15]
K
L
32
/
/{ / B Buttons [TV P.10 / DVD P.15]
[FRONT PANEL]
33 RETURN Button [DVD P.17]
01 POWER Button [TV P.9 / DVD P.15]
02 Disc loading tray
NOTE:
X
Y
03 VOLUME
/
Buttons [P.9]
• We do not recommend the use of universal remote con-
trols as it does not control all the functions. Note that
the code number given by universal remote controls
may not program to this unit. For more details, contact
the manufacturer of the universal remote control.
K
04 CHANNEL SELECT Button [TV P.9]
05 STOP C Button [DVD P.15]
06 PLAY B Button [TV P.9 / DVD P.15]
07 Remote sensor window
• Unless stated, all operations described are based on
remote control use. Some operations can be carried
out using the menu bar on the TV screen.
08 OPEN/CLOSE A Button [DVD P.15]
09 VIDEO input Jack [P.7]
10 AUDIO input Jack [P.7]
11 HEADPHONE Jack
8
EN
TV SECTION
V OPERATION AND SETTINGS
T
INITIAL SET UP
WATCHING A TV PROGRAM
When you turn on the power for the first time,
1 Press [POWER] to turn on the unit.
the INITIAL LANGUAGE screen is displayed.
Select the language for screen display and perform
auto programming of the channels.
NOTES:
-
HELPFUL HINTS
-
1.PLEASE CHECK TO SEE IF
THE ANTENNA/CABLE/
SATELLITE IS
PROPERLY CONNECTED.
2.DID YOU PERFORM
If the TV screen shows snow
noise and there is no operation
for more than 10 seconds,
“AUTO CH PROGRAMMING”?
3.PLEASE REFER TO FRONT
PAGE OF THE OWNER’S
MANUAL OR REAR PANEL
FOR SUPPORT LINE
1 After antenna or cable connection is
completed, connect the power cord into
a standard AC outlet.
“HELPFUL HINTS” appears.
INFORMATION.
• Make sure if the antenna or cable is connected
properly. (Refer to “ANTENNA/CABLE CONNEC-
TIONS on page 6.)
2 Press [POWER] to turn on the unit.
• Set the“AUTO CH PROGRAMMING” in the
CHANNEL SET UP. (Refer to “CHANNEL SET UP”
on page 11.)
3 Press one of the keys listed
SELECT LANGUAGE
below to select the language
• If those setting do not work properly, please
ENGLISH
Y
NEXT:PRESS VOL
H
H
H
of on-screen menu.
• ENGLISH: [VOL.
• ESPAÑOL: [VOL.
ESPAÑOL
DESPUÉS:PRESIONE VOL
FRANÇAIS
APRÈS:PRESSEZ CH.
call our help line on the front page of this owner’s
X
K
manual.
Y
X
]
]
]
K
L
] or the Number buttons to
2 Use [CH.
/
K
select your desired channel number.
• FRANÇAIS: [CH.
To use the number buttons
•Single digit channels: (Ex. 02, 03, 04 and so on)
Press [0] first to select a single digit channel.
4 Confirm the antenna (or cable)
– INITIAL SETUP –
PLEASE CONNECT ANTENNA
OR CABLE OR SATELLITE
TO THIS UNIT.
connection and press [PLAY B].
THEN PRESS PLAY,
• The tuner scans and
memorizes all active
channels in your area.
IN ORDER TO PERFORM
“AUTO CH PROGRAMMING”
•Two digit channels: (Ex. 12, 38, 95 ...)
Press two digits directly.
•Tree digit channels: (Ex. 115, 125 ...)
Press [+100] first, then press the last two digits.
5 When the scanning is completed,
the tuner stops on the lowest
memorized channel.
CH 15
X
Y
] to adjust the volume.
3 Use [VOL.
/
(Example)
Press [MUTE] to instantly
mute the sound. Press it again
to restore the previous sound
level.
VOLUME 20
NOTES:
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
• You can exit the INITIAL SETUP menu by pressing
[SET-UP]. If the button is pressed during channel
scanning, the tuner stops scanning and the lowest
memorized channel is displayed.
NOTE:
• Even if you turn off the unit in the DVD mode, the unit
will be in the TV mode when you turn it on again.
• The INITIAL SETUP menu is displayed every time
you turn on the unit unless the scanning is com-
pleted.
TO WATCH CABLE OR SATELLITE CHANNEL
• In case no channel can be
If the unit is connected to a cable box or satellite
box, use [CH. K / L] to select CH3 or CH4 accord-
ing to the output channel setting of the device and
select desired channel on that device.
received by the channel scanning,
"NO TV SIGNALS" is displayed on
the screen. Turn off the unit and
check the antenna connection,
then follow steps 1 to 5 again.
NO TV SIGNALS
• You can change the setting after completing INI-
TIAL SETUP by LANGUAGE menu or CHANNEL
SET UP menu. (Refer to "ON-SCREEN MENU LAN-
GUAGE" or "CHANNEL SET UP" on page 11).
TO WATCH EXTERNAL INPUT
When an external equipment is
connected to the front AUDIO/
VIDEO input jacks, press
[SELECT] or [CH. K / L] repeat-
edly until "AUX" appears on the
screen.
AUX
9
EN
TV SECTION
TV OPERATION AND SETTINGS
SLEEP TIMER / PICTURE CONTROL
CLOSED CAPTION SYSTEM
You can set Sleep Timer and picture
adjustment with [PICTURE / SLEEP].
TV
TV
TV
TV
You can view specially labeled (cc) TV pro-
grams, movies, news and pre-recorded tapes with
either a dialogue caption or text display.
• The menu changes as described below every time
you press [PICTURE / SLEEP].
1 Press [SET-UP].
- TV SETUP -
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
Sleep Timer
BRIGHT
CONTRAST
COLOR
Use [K / L] to point to
"CAPTION".
B
SHARPNESS
TINT
- TV SETUP -
2 Press [ENTER] repeatedly to
select your desired caption
mode.
SLEEP TIMER SETTING
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [CAPTION1]
The Sleep Timer function is used to turn off the
unit without pressing [POWER] after a desired time.
B
• CAPTION mode: You can watch dramas, movies and
news while captioning the dialogues and the contents
of news.
1 Press [PICTURE / SLEEP] to
SLEEP 0 MINUTE
C
C
C
C
C
C
C
C
C
C
C
C
display the Sleep Timer menu.
• TEXT mode: You can watch half screen text informa-
2 Within 10 seconds, set your desired sleep time
tion if you want.
using [s / B].
*"CAPTION2" is usually used for a second language (if
available).
• [B]...Increase by 10 min. (Up to 120 min.)
• [s]...Decrease by 10 min.
3 Press [SET-UP] to exit the menu.
NOTE:
NOTES:
• To cancel the Sleep Timer, use [CLEAR] or [s / B]
• Even if any power failure, the unit will retain its mem-
ory for this feature.
to set the time to "0".
• Some programs are not broadcasted with closed
captions. The unit is designed to provide error-free
closed captions with high quality antenna, cable and
VCR signals. Conversely, poor quality signals are
likely to result in caption errors or no captions at all.
3 To confirm the remainder time to shutdown,
press [PICTURE / SLEEP].
PICTURE CONTROL
• Common signal conditions which may cause caption
errors are listed below:
The picture controls are preset to factory defaults,
but you can change them to your desired setting.
- Weak snowy reception on TV screen
1 Press [PICTURE / SLEEP]
- Multiplex signal reception displaying picture
ghosts or airplane flutter
BRIGHT
–
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +
repeatedly until desired control
is displayed.
• If the unit displays a black box on
the TV screen, this means that
the unit is set to the TEXT mode.
To clear screen, select "CAP-
TION1", "CAPTION2" or "OFF".
2 Use [s / B] to adjust to your desired level within
5 seconds.
BRIGHT
to decrease brightness to increase brightness
TO CANCEL THE CLOSED CAPTION SYSTEM
CONTRAST to decrease contrast to increase contrast
COLOR
TINT
SHARPNESS to soft
to pale
to brilliant
to green
to clear
1 Press [SET-UP]. Use [K / L] to point to
"CAPTION".
to purple
2 Press [ENTER] repeatedly to select "OFF".
• Even if any power failure occurs, the unit will
retain its memory for this feature.
3 Press [SET-UP] to exit the menu.
10
EN
CHANNEL SET UP
• Refer to page 9 on how to use
the Number buttons.
Channel presetting is necessary at the start
or in case you moved the TV to a different area.
4 Press [ENTER] repeatedly. The channel number
changes to red (deleted) or blue (added) every
time you press the button.
AUTO CHANNEL PROGRAMMING
1 Press [SET-UP].
- TV SETUP -
• To delete or add another channel, repeat steps 3
to 4.
Use [K / L] to point to
B
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
"CHANNEL SET UP", then
press [ENTER].
5 Press [SET-UP] to exit the menu.
NOTE:
2 Use [K / L] to point to "AUTO
CH PROGRAMMING", then
press [ENTER].
– CHANNEL SET UP –
• To confirm that channel(s) has (have) been deleted
or added, select it (them) using [CH. K / L].
ADD/DELETE CH (CATV)
AUTO CH PROGRAMMING
B
The tuner scans and memorizes all the active
channels in your area.
ON-SCREEN MENU LANGUAGE
3 When the scanning is comple-
CH15
You can select the language of on-screen
menu among English, Spanish and French.
ted, the lowest memorized
channel is displayed.
(Example)
If "NO TV SIGNALS" appears
on the TV screen, check the
antenna connection and try
again.
1 Press [SET-UP].
- TV SETUP -
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
Use [K / L] to point to
NO TV SIGNALS
B
"LANGUAGE".
NOTES:
• The unit may recognize CATV channels to be TV
channels if reception condition is poor. In this case,
check the antenna connection and try "AUTO CH
PROGRAMMING" again.
2 Press [ENTER] repeatedly to select "ENGLISH",
"ESPAÑOL" or "FRANÇAIS".
3 Press [SET-UP] to exit the menu.
• Auto channel programming is NOT necessary
when connected to a cable box or satellite box.
Just select the channel for cable box or satellite
input (ex. CH3 or CH4) on the unit, then select
your desired channel on the cable box or satellite
box.
NOTES:
• This function effects only the language on the screen
menu and not the audio source.
• If for some reason the menu is already in Spanish or
French, press [SET-UP], using [K / L] point to
"IDIOMA [ESPAÑOL]" or "LANGAGE [FRANÇAIS]",
then press [ENTER] repeatedly to select desired lan-
guage, then press [SET-UP].
ADDING/DELETING CHANNELS
You can add channels that was not memorized due
to the bad reception status and also delete chan-
nels you no longer receive or seldom watch.
- TV SETUP -
1 Press [SET-UP].
B
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
Use [K / L] to point to
"CHANNEL SET UP", then
press [ENTER].
2 Use [K / L] to point to
"ADD/DELETE CH", then
press [ENTER].
– CHANNEL SET UP –
B
ADD/DELETE CH (CATV)
AUTO CH PROGRAMMING
3 Use the Number buttons or
[CH. K / L] to select your
desired channel number.
(You can also use [K / L] to
enter it.)
08
ADD / DELETE
(Example: CH8)
11
EN
TV SECTION
TV OPERATION AND SETTINGS
A
TV RATING SET UP
V-CHIP SET UP
4 Use [K / L] to select a rating
TV
TV
This feature enables parents to prevent their
children from watching inappropriate material on
TV. When you try to access a blocked program,
“PROTECTED PROGRAM by ...” message appears
on the TV screen.
B
TV–Y
TV–Y7
TV–G
TV–PG (
TV–14
TV–MA(
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
that you wish to block.
(
)
)
)
)
Press [ENTER] repeatedly to
set it to "BLOCK" or "VIEW".
(
Selection Rating Category Explanations
TV-Y
NOTE:
Appropriate for all children
Appropriate for children seven and older
General Audience
Parental Guidance suggested
Unsuitable for children under 14
Mature audience only
• To change the rating, the TV
must be turned to an unprotect-
ed program. If the screen on the
right is displayed, change the
channel to a station that is not
protected.
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
PROTECTED PROGRAM
by TV-Y
1 Press [SET-UP].
NOTES:
- TV SETUP -
• When you select a rating and set
it to "BLOCK", the higher ratings
will be blocked automatically.
The lower ratings will be avail-
able for viewing.
Use [K / L] to select
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
B
TV–Y
TV–Y7
TV–G
TV–PG (DLSV)
TV–14 (DLSV)
TV–MA ( LSV)
[VIEW]
"V-CHIP SET UP", then press
[ENTER].
(
)
[VIEW]
B
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
2 Use the Number buttons to
ACCESS CODE
• When you set the lowest rating to
"VIEW", all other ratings will be automatically avail-
able for viewing.
enter the access code.
_
_
_
_
• For the first time set-up or in
the event the unit has lost
power, enter the default code of 0000.
5 The TV-Y7, TV-PG, TV-14 and
TV-MA ratings have the option
TV–Y
TV–Y7
TV–G
TV–PG (
TV–14
TV–MA(
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
3 Use [K / L] to select an item,
B
(
)
– V-CHIP SET UP –
of sub rating categories.
Use [
K / L] to select a rating
with sub-ratings, then press
)
)
)
then press [ENTER].
Refer to the pages below to
set up each item.
(
B TV RATING
MPAA RATING
CHANGE CODE
[ENTER] twice.
• TV RATING :
• MPAA RATING :
• CHANGE CODE:
P12 A
P13 B
P13
6 Use [K / L] to select a sub-
rating, then press [ENTER] to
set it to "BLOCK" or "VIEW".
TV–PG
[BLOCK]
C
B
D
L
S
V
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
NOTE:
• The blocked sub-ratings will
appear next to the rating cate-
gory in the "TV RATING" menu.
TV–Y
TV–Y7
TV–G
TV–PG (DLSV)
TV–14 (DLSV)
TV–MA ( LSV)
[VIEW]
(
)
[VIEW]
[VIEW]
B
[BLOCK]
[BLOCK]
[BLOCK]
Selection Rating Category Explanations
TV-Y7
FV
Fantasy Violence
TV-PG, TV-14, TV-MA
D
L
Suggestive Dialog (TV-PG, TV-14 only)
Coarse Language
S
V
Sexual Situation
Violence
7 Press [SET-UP] to exit the menu.
12
EN
B
MPAA RATING SET UP
4 Use [K / L] to point to your
desired item, then press
[ENTER] to select "BLOCK"
or "VIEW".
G
[VIEW]
PG
[VIEW]
PG–13
R
NC–17
X
[VIEW]
B
[BLOCK]
[BLOCK]
[BLOCK]
Selection Rating Category Explanations
G
General Audience
PG
PG-13
R
Parental Guidance suggested.
Unsuitable for children under 13
Restricted; under 17 requires acco-
mpanying parent or adult guardian
NC-17
X
No one under 17 admitted
Mature audience only
5 Press [SET-UP] to exit the menu.
C
CHANGE ACCESS CODE
4 Use the Number buttons to
enter your desired access
code in the "NEW CODE",
then enter the same code in
the "CONFIRM CODE". When
completed, the menu will
NEW CODE
X X X X
CONFIRM CODE
_
_
_
_
return to "V-CHIP SET UP".
5 Press [SET-UP] to exit the menu.
NOTE:
• Your personal access code will be erased and will
return to the default (0000) when a power failure
occurs or when you turn off the power using a wall
switch. If you forget the code, unplug the power cord
for 10 seconds to restore the access code to 0000.
13
EN
DVD SECTION
BOUT THE DISCS
A
PLAYABLE DISCS
Playable
discs
Region Recorded Disc
Mark (logo)
Disc types
code
signals size
DVD-Video
*1,2,4,6,10,11
or
Digital
12 cm
Example
DVD-RW
DVD-R
Title 1
Title 2
video
or
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1
Chapter 2
-
-
(MPEG2)
8 cm
*1,3,4,5,6,
7,9,10
DVD+RW
DVD+R
*1,3,4,5,6,8,9,10
Audio CD
* 4,6,10
Example
12 cm
or
8 cm
Digital
audio
-
CD-RW
CD-R
Track 1
Track 2
Track 5
Track 6
Track 3
Track 4
* 4,5,6,9,10
is a trademark of DVD Format/Logo Licensing Corporation.
If you cannot play back a disc which bears one of the marks above, check the following notes.
*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot
be played back.
*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc's producers.
*3: Discs recorded in the VR (Video Recording) format cannot be played back.
*4: Scratched or stained discs may not be played back.
*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the
recorder or special properties of discs.
*6:You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may
not play them back. Even if they are played back, the sound or video quality will be compromised.
*7:You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand's DVD
recorder. However, depending on the recording status of a disc, the disc may not be played back at all
or normally (the picture or sound may not be smooth, etc.). In this case, you need to finalize the disc
with the DVD recorder. Refer to the manual accompanying the DVD recorder.
*8: Only the discs recorded in the video format and finalized can be played back.
Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not
be played back at all or normally (the picture or sound may not be smooth, etc.).
*9: If there is too much recording space left on a disc (the used portion is less than 55mm across), it may
not play back properly.
*10: Do not glue paper or put stickers on to the disc. These may damage the disc and the unit may not read
it correctly.
*11: The number inside the symbol refers to a region of the world and a disc encoded in a specific region
format can only be played back on unit with the same region code.
UNPLAYABLE DISCS
• NEVER play back the following discs. Otherwise, malfunction may result!
DVD-RAM / CD-i / Photo CD / Video CD / DVD-Audio / DVD with region codes other than 1 or ALL /
DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers / MP3
• The sound MAY NOT be heard: Super Audio CD
NOTE:
Only the sound recorded on the normal CD layer can be delivered. The sound recorded on the high density Super Audio
CD layer cannot be delivered.
• Any other discs without compatibility indications
14
EN
|