RHK900 (SBT600ss) for USA
24-11-2014
Sonic Boom Alarm Clock & Bed Shaker
with 5-Level Dimmer & USB Charging
Model SBT600ss
OPERATION INSTRUCTIONS
IMPORTANT – Please read these instructions carefully before use and retain for future reference.
See operating instructions on back.
– Use only the supplied adaptor to connect the unit.
Warning: To prevent fire or shock hazard do not expose this appliance to rain or moisture.
Before connecting to mains make sure that the requirements specified on the apparatus
corresponds to the available power supply i.e. AC100-240V~, 50/60 Hz.
– The ventilation should not be impeded by covering the ventilation openings with
items such as, newspaper, table cloth, curtains, etc;
– No naked flame sources, such as lighted candles should be placed on the apparatus.
– It shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
– Do not place the product in closed bookcases or racks without proper ventilation.
– Where the mains plug is used as the disconnect device, the disconnect device shall
remain readily operable.
RHK900 (SBT600ss) for USA
24-11-2014
Setting the correct time –
1) Press and hold the Time Set Button (1) at the same time press the Hour Button (2) to
advance the clock display rapidly until the hour is correct.
2) Press and hold the Time Set Button (1) at the same time press the Minute Button (3) to
advance the clock display rapidly until the minute is correct.
A lighted dot (8) in the upper left of the clock display indicated the time is PM. For AM time
indication, the dot does not light up.
Setting the alarm time –
1) Press and hold the Alarm Set Button (4) at the same time press the Hour Button (2) to
advance the alarm display rapidly until the hour is correct.
2) Press and hold the Alarm Set Button (4) at the same time press the Minute Button (3) to
advance the alarm display rapidly until the minute is correct.
3) Make sure the alarm time is correctly set for AM or PM, the lighted dot (8) indicated PM.
Please be sure to release the HOUR and MIN set buttons before releasing the ALARM button.
Selecting 12 or 24 hours format –
1) Press and hold the Hour button (2) for 6 seconds to enter the hour selection mode, release
the Hour button (2) when the display shows "12 H" or "24 H".
2) Press and release the hour button to toggle between 12 or 24 hours. If no selection is made
within 4 seconds, then the last displayed hour format will be chosen and the display will
return to the normal Time mode.
Waking to Alarm –
1) If only the buzzer is required, do not plug in the vibrator.
2) Set desired volume using the Volume wheel (12) for buzzsound.
3) If only vibrator is required, the plug in the vibrator into Vibrator socket (14) and turn off the
volume by using the Volume wheel (12).
4) If both the Buzzer and vibrator are required, plug in the vibrator and set the volume to the
desired level.
5) Set alarm wake time per instructions for setting alarm time above.
Adjusting The Alarm Duration Time
The default alarm duration time setting is 30 minutes, you may adjust the alarm duration between 1
minute and 59 minutes as desired. To adjust the alarm duration:
1) Press and hold the AL. SET button (4) for six seconds. The clock display will show the
default alarm duration as ‘30’, release the AL. SET button.
2) Press the MIN button (3) to adjust the alarm duration to the desired setting, from 1 minute to
59 minutes.
3) When the display is showing the desired alarm duration time, it will return to the normal
clock mode after 3 seconds. The new alarm duration time setting becomes the new default
and remains in the memory until you change it again.
Shutting Off Alarm –
Alarm can be shut off temporarily for the day or shut off permantently.
1) When the alarm goes off, simply press the AL off button (4) the alarm will shut itself off for
the day and come back on the next day at the same time if the alarm setting has not changed.
2) To shut off the alarm permanently, slide ON/OFF Switch (5) to off positon. The alarm will
not come on until ON/OFF Switch (5) is set to on position again.
Snooze Operation–
SNOOZE button (6) – press after alarm has sounded. The alarm will be turned off for 9 minutes for
extra sleep. The alarm will come back again after 9 minutes. You may repeat many time up to 119
minutes .
RHK900 (SBT600ss) for USA
24-11-2014
Adjusting The Snooze Time
The default snooze time setting is 9 minutes but you may adjust the snooze time between 1 minute
and 30 minutes as desired. To adjust the snooze time:
1) Press and hold the SNOOZE button (6) for four seconds. The clock display will show the
default snooze time ‘9’. Release the Snooze button.
2) Press the “ MIN“ button (3) to adjust the snooze time to the desired setting, from 1 minute
to 30 minutes.
3) When the display is showing the desired snooze time, it will return to the normal clock mode
after 3 seconds. The new snooze time setting becomes the new default and remains in the
memory until you change it again.
Volume –
To adjust the volume rotate the Volume wheel (2) until you have reach the desired level.
Tone –
Adjust the tone by rotating the Tone wheel (10) until you have reach the desired level.
Dimmer Operation
There is a 5-level brightness control for the LED display. Press the SNOOZE button (6) once to
change the display brightness. The brightness will cycle from 5-4-3-2-1-2-3-4-5 (from bright to dim
then from dim to bright).
*NOTE*: The dimmer function will not work, when the clock is in snooze mode.
Bed Shaker / Vibrator
1) Attach the bed shaker jack to the back of the clock at VIBRATOR input (14).
2) Place vibrator under mattress or pillow.
USB Charging
This alarm clock is equipped with a convenient USB charging port on the back panel that allows you
to recharge many brands of mobile phones, portable music players, and other handheld devices that
are supplied with USB charging cables. The output rating of the USB charging port is 500mA.
To charge your device, connect the USB charging cable that was supplied with your handled device
to the USB charging port (13) on the back panel of this alarm clock. Observe the charging indicator
on your device to confirm that it is charging.
Note: Charging time will vary depending on the charging current that your device requires.
Therefore some devices will take longer to charge than others.
Battery Backup –
To use the battery backup, you can install 1 pieces of 9V size battery at the base of the clock under
the battery cover (7). Please note the LED display will not show during power failure but the clock
will still be running and keeping proper time until the power is restored.
NOTE: For the best results it is recommended that the battery be changed every 6-8 months. If the
clock is not used for a while, it is recommended to remove the battery to aviod leakage.
DC 5V Power Input –
Attach the DC power supply input to the back of clock labeled DC5V
IN (11 ).
GENERAL DATA
UL listed Power Adaptor: AC100-240V~, 50/60Hz
Power Consumption: Adaptor Output: DC5V
USB Charging Port Rating: 500mA
, 800mA
RHK900 (SBT600ss) for USA
24-11-2014
CAUTION:
TO REDUCE THE RISK
OF ELECTRICAL SHOCK,
DO NOT REMOVE THE
COVER (OR BACK) FROM
THE PRODUCT. NO USER
SERVICEABLE PARTS
INSIDE. REFER
The Lightening flash and
arrowhead within the
triangle is a warning sign
alerting you of dangerous
voltage inside the product.
The exclamation mark
within the triangle is a
warning sign alerting you
of important instructions
accompanying the product.
SERVICING TO YOUR
SONIC ALERT DEALER.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
Normal function may be disturbed by strong electromagnetic interference. If this is
the case, normal function can be resumed by simply unplugging and plugging of the
power adaptor. If function does not resume, try moving the unit to another location.
-
-
Attention should be drawn to the environmental aspects of battery disposal.
this indicating separate collection for electrical and electroinc equipment.
SONIC ALERT'S 1 YEAR LIMITED WARRANTY
The Sonic Boom Alarm Clock is warranted against manufacturing defects in materials and
workmanship for one (1) year from the date of purchase. Within this period Sonic Alert will
repair or replace at our option without charge for parts and labor. Simply contact our customer
service department to obtain an RA (return authorization number) and instructions on how to
process your product for return. Call 1-888-864-2446 or e-mail to [email protected]. You'll
need a copy of your receipt to process the return authorization.
Sonic Alert Warranty Center, 1081 West Innovation Dr., Kearney, MO 64060
Sonic Alert
Sonic Alert 1050 East Maple Rd. Troy, MI 48083
www.SonicAlert.com 1-888-864-2446
Made in China
|