Sonic Alert Clock Radio SBD375ss v3 User Manual

Sonic Boom Dual Alarm Clock with Bed Shaker  
Model SBD375ss-v3  
OPERATION INSTRUCTIONS  
IMPORTANT – Please read these instructions carefully before use and retain for future  
reference. See operating instructions on back.  
– Use only the supplied or recomended Sonic Alert adaptor to connect the  
unit.  
Warning: To prevent fire or shock hazard do not expose this appliance to rain or  
moisture. Before connecting to mains/ power make sure that the  
requirements specified on the apparatus corresponds to the available power  
supply in that country i.e. AC100-240V~, 56/60 Hz.  
– The ventilation should not be impeded by covering the ventilation  
openings with items such as, newspaper, table cloth, curtains, etc;  
– No naked flame sources, such as lighted candles should be placed on the  
apparatus.  
– It shall not be exposed to dripping or splashing and that no objects filled  
with liquids, such as vases, shall be placed on the apparatus.  
– Do not place the product in closed bookcases or racks without proper  
ventilation.  
– Where the mains/ power plug is used as the disconnect device, the  
disconnect device shall remain readily operable.  
 
Setting Alarm 2  
4) Once alarm AL1 has been set, slide “ALARM SELECTOR“ (1) to AL2 position. , the  
alarm indicator “AL2“ (13) will light up.  
5) Slide the “ALARM SELECTOR“ (1) to AL2 position, the alarm indicator “AL2“ (13) will  
light up.  
6) Press and hold the “ALARM SET /OFF“ (5) button and at the same time press the  
“FAST“ Button (6) or the “SLOW“ button (7) to advance clock display until you reach  
desired alarm setting.  
Selecting 12 or 24 hours format – Clock is set to 12 hour as the default setting  
Press and hold the Fast Button (9) for 6 seconds to enter the hour selection mode,  
release the Fast Button (9) when the display shows "12 H" or "24 H". Press and release  
the hour button to toggle between 12 or 24 hours. If no selection is made within 4 seconds,  
then the last displayed hour format will be chosen and the display will return to the normal  
Time mode.  
Alarm –  
Enable Alarms:  
1) To enable Alarm 1, slide the “ALARM SELECTOR“ (1) to AL1 position. the alarm  
indicator “AL1“ (12) will light up.  
2) To enable Alarm 2, slide the “ALARM SELECTOR“ (1) to AL2 position, the alarm  
indicator “AL2“ (13) will light up.  
3) To enable both alarms, slide the “ALARM SELECTOR“ (1) to AL2 position, the alarm  
indicators “AL1“ (12) and “AL2“ (13) will light up.  
To Select Wake up mode  
To select the wake up mode, slide the “Alarm Mode Switch“ (11) to your desired position:-  
a) “BUZZ“ for sound b) “VIB“ for bed shaker c) “VIB/ BUZZ“ for both sound and bed  
shaker  
NOTE: once the wake up mode is chosen, this will apply to both alarms.  
Alarm Patterns –  
When the alarm is activated, alarm pattern of the buzzer / flashing display will be out of sync  
with the vibrator. This means that when the buzzer / flashing display is ON, the vibrator will  
be OFF and while the buzzer/ flashing display is OFF, the vibrator will be ON.  
ALARM 1 - When Alarm 1 is activate, it will have 3 beeps for buzzer, then the vibrator.  
This pattern is repeated until the alarm is stopped.  
ALARM 2 - When Alarm 2 is activate, it will have 4 beeps for buzzer, then the vibrator.  
This pattern is repeated until the alarm is stopped.  
Adjusting The Alarm Duration Time  
The default alarm duration time setting is 30 minutes; you may adjust the alarm duration  
between 1 minute and 59 minutes as desired. To adjust the alarm duration:  
Press and hold the AL. SET button (5) for six seconds. The clock display will show the  
default alarm duration as ‘30’. Release the AL set button  
Press the “ MIN” button (10) to adjust the alarm duration to the desired setting, from 1  
minute to 59 minutes.  
When the display is showing the desired alarm duration time, it will return to the normal  
clock mode after 3 seconds. The new alarm duration time setting becomes the new  
default and remains in the memory until you change it again.  
Snooze Operation –  
1. When the alarm turns on in the morning you may press the SNOOZE Button (8) to stop  
the alarm temporarily. The alarm will shut off for 9 minutes or for the predetermined time  
you select from 1-30 minutes, and then turn on again. The snooze operation may be  
repeated indefinitely until the alarm is turned off.  
2. The SNOOZE function of Alarm 1 and Alarm 2 is independent of each other.  
 
Adjusting The Snooze Time  
The default snooze time setting is 9 minutes but you may adjust the snooze time between 1  
minute and 30 minutes as desired. To adjust the snooze time:  
Press and hold the SNOOZE Button (8) for four seconds. The clock display will show  
the default snooze time ‘9’. Release the snooze button  
Press the “SLOW“ Button (7) to adjust the snooze time to the desired setting, from 1  
minute to 30 minutes.  
When the display is showing the desired snooze time, it will return to the normal clock  
mode after 3 seconds. The new snooze time setting becomes the new default and  
remains in the memory until you change it again.  
Shutting Off the Alarm –  
Alarm can be shut off temporary for the day or permanently shut off.  
1) When alarm goes off, press the “ALARM SET/OFF“ (5) button to turn off for the day and  
come back on at the same time the next day, if alarm settings have not changed.  
2) To shut the alarm off permanently, slide the “ Alarm Mode Switch“ (11) down to the OFF  
position. The alarm will not come on until the “ Alarm Mode Switch“ (11) is set to  
“VIB/BUZZ“, “VIB“, or “BUZZ“ position.  
NOTE: The Alarm Off function of Alarm 1 and Alarm 2 is independent of each other.  
Dimmer Operation  
There is a 5-level brightness control for the LED display. Press the SNOOZE button once to  
change the display brightness. The brightness will cycle from 5-4-3-2-1-2-3-4-5 (from bright to dim  
then from dim to bright).  
*NOTE*: The dimmer function will not work, when the clock is in snooze mode.  
Volume Control –  
1) To adjust the volume, rotate VOLUME wheel (12) located on the lower right corner of the  
clock.  
Tone Control –  
1) To adjust the TONE, turn the TONE wheel (10) located on the top right corner of the clock.  
Bed Shaker / Vibrator –  
1) Attach the bed shaker jack to the back of clock at “VIBRATOR INPUT“ (15).  
2) To turn on vibrator slide “Alarm Mode Switch“ (11) to “VIB/BUZZ“ or “VIB“ position.  
3) Place vibrator between mattress and box spring.  
Bed Shaker / Vibrator Strength Control  
Slide the Vibrator Strength switch (2 ) to adjust the vibrator strength, Hi setting is the  
stronger and the Lo setting is the weaker.  
Battery Backup –  
To use the battery backup, you can install a 9-volt alkaline battery in the back of the clock located  
under the Battery Compartment Cover (17). The battery needs to be purchased separately.  
Note the LED display will not show during power failure but the clock will still be running  
and keeping proper time until the power comes back. During a power failure, the alkaline  
battery can only keep the clock IC running for up to 30 days. (During a Power failure, the LED  
display will not show the time.)  
NOTE: For the best results it is recommended that the battery be changed every 6 months. If the  
clock is not used for a while, it is recommended to remove the battery to avoid damage to the  
clock from battery leakage.  
 
DC 9V Power Input –  
Attach the “DC POWER INPUT“ (16) to the back of DC9V IN next to “VIBRATOR  
INPUT“ (15); it is the smaller input of the two.  
NOTE: IMPORTANT: do not confuse “DC POWER INPUT“ (16) with the “VIBRATOR  
INPUT“ (15)  
GENERAL DATA  
UL listed Power Adaptor: AC100-240V~, 50/60Hz  
Power Consumption: Adaptor Output: DC9V  
, 650mA  
CAUTION:  
TO REDUCE THE RISK  
OF ELECTRICAL  
SHOCK, DO NOT  
REMOVE THE COVER  
(OR BACK) FROM THE  
PRODUCT. NO USER  
SERVICEABLE PARTS  
INSIDE. REFER  
The Lightening flash and  
arrowhead within the  
triangle is a warning sign  
alerting you of dangerous  
voltage inside the product.  
The exclamation mark  
within the triangle is a  
warning sign alerting you  
of important instructions  
accompanying the  
SERVICING TO YOUR  
SONIC ALERT DEALER.  
product.  
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS  
APPLIANCE TO RAIN OR MOISTURE.  
The normal function of the product may be disturbed by Strong Electro Magnetic  
Interference. If so, simply reset the product to resume normal operation by  
following the instruction manual. In case the function could not resume, please  
use the product in other location.  
Attention should be drawn to the environmental aspects of battery disposal.  
this indicating separate collection for electrical and electroinc equipment.  
 
SONIC ALERT’S 1 YEAR LIMITED WARRANTY  
The Sonic Boom Alarm Clock Model SBD375ss is  
warranted against manufacturing defects in materials and  
workmanship for one (1) year from the date of purchase.  
Within this period Sonic Alert will repair or replace at our  
option the SBD375ss without charge for parts and labor.  
Simply contact our customer service department to obtain an RA  
(return authorization number) and instructions on how to process your  
product for return. Call 1-888-864-2446 or e-mail to  
[email protected]. You’ll need a copy of your receipt to process  
the return authorization.  
Sonic Alert Inc., Troy MI 48083, USA.  
Sonic Alert  
Made in China  
Sonic Alert , Troy, MI 48083  
www.SonicAlert.com 1-888-864-2446  
 

Sharp CRT Television 32U S50B User Manual
Sony Film Camera HXC 100 User Manual
Sony MiniDisc Player MZ E45 User Manual
Sony Projector VPL CS2 User Manual
Stamina Products Bicycle 15 4760 User Manual
StarTechcom TV Cables dvi2hdmia User Manual
Stiga Trimmer SH 160 User Manual
Stovax Indoor Fireplace 8544LUC P8544LUC User Manual
Sunbeam Hot Beverage Maker KE7600B User Manual
Symphonic VCR VR 701 User Manual